3 Pack Galaxy S23 Ultra Screen Protector Tempered Glass 3D Curved Edge 100% Fingerprint Unlocking, Scratch & Impact Protection HD Clear & Smooth Touch for Samsung S23 Ultra

4.5 stars rounded up to 5 assuming you get one that the glass is perfect. After I had mine installed I noticed from a certain angle there was a very very slight small dimple in the glass. There's no way you can see it from most angles or when the screen is on but it indicates as other reviewers stated the weight isn't well secured to it can slightly dent the glass if your package happened to be handled without care. So minus 0.5 stars for that. The glass is very fragile too but that's why they give you multiples of them. They are meant to sacrifice themselves to protect your phone's actual glass screen, not meant to be bulletproof for years.Got this for a lower price than the similar adhesive UV-based tempered glass protectors from name brands. The application process is virtually identical. Just be careful to follow the instructions in the video to a tee. Don't do this in an impatient rush! (Or you'll be a < 4 star reviewer) Also note, the glass with UV adhesive type protectors are the only glass protectors that will both work well with the fingerprint reader and not have a visible circle where the fingerprint sensor is. You will be tempted to buy the cheaper stick-on glass protectors but they will either not work well with the fingerprint reader or will have an ugly circle on the protector where it is. Your only other option is a plastic film protector which will not maintain the smooth glass finish like glass will but will work as long as you don't mind replacing it once in a while.Here are my tips to ensure a successful application:- Remove your S-Pen so the bottom of your phone is flat when you put the sticker on it.- IGNORE any reviewers recommending a specific amount of drops of adhesive. They put the amount of adhesive in the little bottle for a reason. Do not worry about making a mess, the excessive adhesive is easy to clean off the sides of your phone and very little gets on it. It's nothing like super glue even after cured. Have a paper towel ready to dab and/or wipe the sides and your fingers. If you do not apply enough adhesive you will need to start over and throw away the protector! If you get a very small bubble near the edge you can *maybe* gently push it with two fingernails like you are trapping it and move it down and off the edge or corner but if you have a large bubble or dust you can't lift the protector and fix it. You'll need to toss the protector and start with a new one.- If you want to be extra cautious (like me) I applied scotch tape around all edges of the phone so I could easily peel it off and didn't have excess adhesive to wipe off the phone. However on the sides, only apply the scotch tape about 2/3 up the edge so the tape edge doesn't come too close to the edge of the protector. Just enough to cover the buttons. Otherwise you'll end up glueing the scotch tape to the edge of the glass and when you lift the scotch tape up you'll lift the protector up and have to throw it away and start over (I found this out the hard way.)- Make sure there are no bubbles in the adhesive before you lower the protector. It should be a perfectly clear pile of adhesive. Stir it surg the tip of the bottle to get any tiny bubbles out.- Note that the back protective film on the glass sometimes does not peel off when you remove the sticker so you need to use your fingernail to peel it off. But be careful because you can easily break or contaminate the glass.- After removing the phone so you can apply the UV light to the edges. Before applying the light wipe the edges of the phone with the leftover alcohol wipe then a paper towel then the little cloth wipe. This will ensure you don't have any cured adhesive just past the edges of the glass (which isn't hard to clean off if you do but best to make sure the phone edges are clean before applying the UV light.)- The alignment tool will by default leave more of a space at the top of the phone than the bottom unless you use the slider to push the glass up more. I prefer to have the larger gap at the top and a very tiny gap at the bottom. WHY? Because after you put a case on, the glass will meet or be slightly under the bottom of the case so when you do your swipe gestures from the bottom of the glass edge up, you won't feel the edge of the protector. When the glass is aligned like this, the top of the glass edge is perfectly aligned with the top edge of the actual lit up display and just covers the entire camera. Plus it's very hard to see the gap anyway. So I recommend just sticking with the default alignment of having a larger gap at the top.- FINALLY, there's a decent chance (venture to guess 1 out of 3 chance) that you may end up with one or two very very tiny bubbles or dust specs as we all don't install these in a "clean room" lab. If you are OCD, then fine, toss the protector and start over. BUT, for the rest of us, if that happens I recommend you just accept it. Why? I guarantee you won't notice one or two tiny specs under the glass the next day and forward. You will only notice them if you look for them (which you will do right after you install it.) In my opinion it's WAY better to save the extra protector for later when you might REALLY need them to replace a cracked protector.OVERALL: Great value for tempered glass UV adhesive protector. Easier to install than it sounds if you follow the video and my tips. Fit the phone perfect with slight space for phone case edge. Glad I chose this over film even though application is a little more complicated. Not for the impatient and in a hurry.Fingerprints may or may not work after but they definitely work a lot better if you retrain your fingerprints after installing the protector.

HOT Garbage.As a geometry engineer, let me say that if you get this kit to work, consider yourself very lucky. The alignment jig has no datum, aka a place where the glass hits a hard plastic stop and produces accurate and repeatable alignment. Therefore the functionality and ease of installation is totally flawed from the get go. Then the manufacturer has the nerve to say 99.99% of the users who fail didn't watch the video. Haha, what a joke.I've used other branded kits before (ones approx $5-10 more on Amazon) without any of these issues. I was basically robbed while trying to save a few bucks because now I need a whole new kit. Yes, all 3 glass protectors failed within a week. Edge peeling, air bubbles in touching areas (2 dots of glue is horrible instruction, the glue is too thin and will run out the edges before it's spread across whole screen).Once an edge peels.... It only gets worse. Amazon support suggest using clear tape! Haha, no they seriously say that. If you're lucky and an edge does NOT peel, you'll still end up with air bubbles thanks to the glue being too watery / extra time to "adjust" the glass alignment manually since the alignment jig doesn't work as it should.Do yourself a favor and stay far away from this kit, and probably company. No way to contact them, no email link, nothing.

I don't know why these don't have better reviews. I followed the video of the directions, and my fingerprint works great, the keyboard works great for text and everything else. I purchased a different screen saver first because these only having a 3.9 review. The other screen saver was one where the with the fingerprint reader shows all the time on the screen. I didn't really care for that as I found it annoying. But I could live with it as long as the fingerprint reader worked. When installing you had to rub the reader area down to make a good connection with the glass on your phone. After about 1 hour the adhesive started to pull away from the glass on the phone and the fingerprint quit working. If I rubbed it back down the fingerprint worked again for about 30 minutes, then it started to separate from the glass again. After a few days I gave up on the fingerprint but then texting was getting very hard. I can only assume it because the glass protector was separating from the glass on the phone. So, I trashed it and got this product. It works GREAT if you follow the instructions and no annoying fingerprint reader showing on the protector.