Inline air gap with 1/4-inch FIP or 1/2-inch Thread Inlet and 5/8-inch Compression Fitting or 3/4-inch Thread Outlet. (AG150-001, 211211, GAP-A-FLO)
Thumbnail 1Thumbnail 2Thumbnail 3Thumbnail 4Thumbnail 5Thumbnail 6

Inline air gap with 1/4-inch FIP or 1/2-inch Thread Inlet and 5/8-inch Compression Fitting or 3/4-inch Thread Outlet. (AG150-001, 211211, GAP-A-FLO)

3.7/5
Product ID: 27603980
Secure Transaction
Frequently Bought Together

Description

  • ❤ EASY TO CONNECT: Gap-A-Flo air gap (AG150-001) has a 1/4-inch FIP or 1/2-inch MIP threaded inlet and 5/8-inch compression fitting OD outlet with 3/4-inch thread outlet connection. The inlet accommodates 1/4-inch FIP or 1/2-inch threaded PVC adapters, while the outlet can accommodate 3/8-inch FIP, 3/4-inch threaded PVC adapters, or 5/8 OD tubing. The convenient design of the AG150-001 allows it to be tilted at any angle down as low as 45 degrees.
  • ❤ STANDPIPE CONNECTION: Gap-A-Flo air gap (AG150-001) is a gravity flow device and must have an outlet poly tubing feeding directly to a drain without kinks or bends. It can be oriented in any way between 45 degrees and vertical with inlet port elevated above the outlet port. To ensure easy wall mounting, a Jiffy Clip clamp is included with the air gap. The air gap outlet is tested at 15 gallons per minute, and recommended use is 7 gallons per minute.
  • ❤ SPLASH PROTECTION: The AG150-001 air gap uses rotating splash guards to assure a completely dry operation. Splash guards are an integral part of the design and can be seen through the side air gap window. During water softener operation, an initial discharge surge can create splashing. Splash shield eliminates the possibility of water splashing outside of the air gap. When designing drainage for an air gap, makes sure that P-trap is located minimum 20-inches from the top of the standpipe.
  • ❤ QUIET OPERATION: When water exits the air gap, depending on the design, it may flow directly into a P-trap. This can create splashing noise that may be objectionable. To avoid excessive noise, it is recommended to use 22 degrees elbow in line with standpipe to avoid direct drainage to P-trap. The pipe elbow should be located at least 12 inches from the air gap to eliminate splashback.
  • ❤ CERTIFICATION: The AG150-001 is UPC (Uniform Plumbing Code) Listed, IPC (International Plumbing Code) and NSF (National Sanitation Foundation) tested. The testing is conducted for every manufactured lot to ensure consistent performance.

The AG150-001 Universal Inline Air Gap is designed to isolate potable water supply from drainage water. It can be used for RO filter systems, water softeners, well water filters, boilers or with any other equipment that requires an air gap discharge to the drain. This air gap is perfect for applications where a rigid Schedule-40 pipe must be plumbed to an approved air gap device. The AG150-001 is the only air gap that can be installed at up to 45 degrees angle if necessary. A rotating air gap shield is provided to completely protect air gap from debris ingress, which can cause air gap malfunctioning. This air gap is easy to use, easy to install, and easy to maintain. The AG150-001 air gap is listed by UPC and tested for compliance with IPC and NSF standards.

Reviews

3.7

All from verified purchases

A**R

Expensive

Expensive

J**M

Works fine for my water softener drain

The softener drain needs to have an air gap if discharging into a sewer line or floor drain. Since my water softener's maximum drain rate is only 2.2 GPM, this air gap worked fine with a T into the humidifier's 3/4" drain line which went to a floor drain. Because of the location of the floor drain, I decided to use an inline gap instead of just holding the drain line away from the floor. Note to be careful (I should have known better) if using a wrench on the bottom of the unit to tighten a connection on the top. I got an internal crack that initially was fine when I tested the softener discharge but then leaked when the softener recycled during the night.

A**R

Great product! AND

Great product! AND....great support. I had a difficult routing of the drain and they engineered me out of a bind. Good company!

A**R

Be careful

Water just flowed right out the opening.....I may be an idiot, but this product seems like a really bad idea unless the water is just trickling out of hose.

R**N

One Star

No ASTM # cant be used in MN

Common Questions

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Suresh K.

Very impressed with the quality and fast delivery. Will shop here again.

4 days ago

Ali H.

Fast shipping and excellent packaging. The Leatherman tool feels very premium and sturdy.

1 day ago

Shop Global, Save with Desertcart
Value for Money
Competitive prices on a vast range of products
Shop Globally
Serving millions of shoppers across more than 100 countries
Enhanced Protection
Trusted payment options loved by worldwide shoppers
Customer Assurance
Trusted payment options loved by worldwide shoppers.
Desertcart App
Shop on the go, anytime, anywhere.
£34.85

Duties & taxes incl.

UKstore
1
Free Shipping

with PRO Membership

Free Returns

30 daysfor PRO membership users

15 dayswithout membership

Secure Transaction

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Farhan Q.

The delivery time was excellent, and the packaging was secure.

2 months ago

Sneha T.

Received my product in pristine condition. Great service overall.

1 month ago

Inline Air Gap With 1 4 Inch Fip Or 1 | Desertcart GB